Products to Compare (max of 3)
X
Compare These Parts
America's Oldest Speed Shop ® Talk to the Experts. Call 800.979.0122, 7am-10pm, everyday.
Help Center
Help Center

U.S.Order Line:

800.979.0122

(CST) 7am - 10pm

Race and Rod Tech Support

Mon-Fri 8am - 5pm

Canadian Order Line:

855.313.9180

International Order Line:

1.402.323.3200
Since 1952
Menu
Shop By
Support
Account
Add to Cart
$59.99
$29.99
Garage Sale - 1950 Pontiac LED Tail Light Conversion Lens
Garage Sale - 1950 Pontiac LED Tail Light Conversion Lens

Garage Sale - 1950 Pontiac LED Tail Light Conversion Lens

0 Reviews | 0 Answered Questions
In Stock
Can Ship FREE
Garage Sale - 1950 Pontiac LED Tail Light Conversion Lens
Image Gallery
Garage Sale - 1950 Pontiac LED Tail Light Conversion Lens
Garage Sale - 1950 Pontiac LED Tail Light Conversion Lens
Zoomed In Image
Part # UP62972
Save 50%
$29.99
$59.99
set
Quantity:
Add to Cart
Call to Order
Add to Buildlist
Compare

Details
Reviews
Q&A
Articles

Important Messages:

  • Get FREE shipping when your order includes this item and exceeds $99! Ground shipping only in the contiguous US.

Details

Info

This item is garage sale priced because it only includes enough pieces for a single side.

 

**No Warranty, No Returns On Garage Sale Items** 

 

This 1950 Pontiac LED tail light conversion kit converts your 50 Pontiac tail, stop, and turn signal lights into very bright and visible LEDs. LEDs feature a wide viewing angle of 100 degrees as well as cool operation and long life. This kit is designed to bolt into a 1949-52 Ponitac taillight housing with the provided stainless steel brackets. Your stock lenses are reused for a factory appearance when the lights are off. A true bolt-in for stock Pontiac taillight housings or reproduction units.

Kit Contents:

  • (1) LED arrays
  • (4) solderless connectors
  • (1) LED to car electrical harness
  • Installation instructions

The red wire is for stop light/turn signal. The black wire is for the tail light.

1950 Pontiac LED Tail Light Conversion Instructions (PDF)

Item Details

'Uses YOUR ''50 Pontiac housings'

Notes

  1. The original housing and bulb socket grounded through the base where it bolted to the body by the mounting studs.
  2. When wiring up the conversion, the black wire goes for the tail lights and red wire for the stop and turn lights.
  3. There is a green wire that needs to be routed past the grommet and the eye on the wire must go on the mounting stud and make good contact to the metal body surface for proper grounding. If you are using this light on a fiberglass body you will need to run a lead from the green wire to an appropriate ground.

 

Specs

  • Circuit board with attached pigtail only - NO lens is included
  • 8 sided circuit board that is 2 1/4" by 2 5/16"
  • 5/16" thick including 14 LEDs
  • Central mounted attachment stud extends 2 1/8"
  • A tab strap extends outward from two opposing sides 7/8" on each side for the original tail light studs to pass through
  • Overall width of the attachment strap is approximately 4"
  • Stud has sealing grommet for weather tight attachment
  • Wiring Guide:
    • Red wire - Stop light/Turn signal
    • Black wire - Taillight
    • Green wire - Ground
Some parts are not legal for use in California or other states with similar laws/regulations

Related Products

More Like This

Reviews

Q & A

Articles

You May Also Like

Suggestions
Error
Note
Ok