Products to Compare (max of 3)
X
Compare These Parts
America's Oldest Speed Shop ® Talk to the Experts. Call 800.979.0122, 7am-10pm, everyday.
Help Center
Help Center

U.S.Order Line:

800.979.0122

(CST) 7am - 10pm

Race and Rod Tech Support

Mon-Fri 8am - 5pm

Canadian Order Line:

855.313.9180

International Order Line:

1.402.323.3200
Since 1952
Menu
Shop By
Support
Account
Add to Cart
$39.99
$29.99
Garage Sale - 11 Inch Mustang II Rotor with GM 4.75 Inch Bolt Circle, Metric Caliper
Garage Sale - 11 Inch Mustang II Rotor with GM 4.75 Inch Bolt Circle, Metric Caliper

Garage Sale - 11 Inch Mustang II Rotor with GM 4.75 Inch Bolt Circle, Metric Caliper

0 Reviews | 0 Answered Questions
In Stock
Can Ship FREE
Garage Sale - 11 Inch Mustang II Rotor with GM 4.75 Inch Bolt Circle, Metric Caliper
Image Gallery
Garage Sale - 11 Inch Mustang II Rotor with GM 4.75 Inch Bolt Circle, Metric Caliper Garage Sale - 11 Inch Mustang II Rotor with GM 4.75 Inch Bolt Circle, Metric Caliper Garage Sale - 11 Inch Mustang II Rotor with GM 4.75 Inch Bolt Circle, Metric Caliper Garage Sale - 11 Inch Mustang II Rotor with GM 4.75 Inch Bolt Circle, Metric Caliper
Garage Sale - 11 Inch Mustang II Rotor with GM 4.75 Inch Bolt Circle, Metric Caliper
Zoomed In Image
Part # UP76774
Save 25%
$29.99
$39.99
each
Quantity:
Add to Cart
Call to Order
Add to Buildlist
Compare

Details
Reviews
Q&A
Articles

Important Messages:

  • Get FREE shipping when your order includes this item and exceeds $99! Ground shipping only in the contiguous US.

Details

Info

This is garage sale priced because bearings and seals have been installed.

No Warranty, No Returns on Garage Sale Items    

 

This rotor allows the use of GM Metric calipers along with a GM car bolt pattern. Vented stock 11" diameter brake rotors for 1974-1980 Mustang II, Pinto, or Bobcat spindles (or popular GM Metric calipers and brackets). Brake rotors are new, not plugged or re-drilled. Has a 5 on 4-3/4" bolt pattern with corresponding 7/16" diameter fine thread wheel studs.
  • 5 on 4.75" Bolt circle
  • Granada type rotor
  • For use with popular GM Metric calipers and brackets
  • Bearing and seal kit sold separately (910-31052)

Notes

Proper Break-In Procedure for Steel or Cast Iron Rotors

New steel/iron rotors should be bedded in before being used in racing conditions. Proper bedding will prepare the rotor surface, prolong the rotor's life, and make it more resistant to thermal checking or cracking under severe braking conditions. The following procedures should be performed when bedding in both steel and cast iron rotors. It is best to bed in a new rotor using a used set of pads, preferably ones which will not create heat rapidly. Generating heat too rapidly will thermal shock the rotors. Likewise, when bedding in a new set of brake pads it is best to perform the process on a used rotor. This new/used bedding process permits controlled bedding of each individual component.

Make sure rotor surfaces are free from oils, grease, and brake fluid. Run vehicle up to a moderate speed and make several medium deceleration stops to heat up the rotor slowly. This will help reduce the chance of thermal shock caused by uneven heating of the rotor. Pull into the pits and allow the rotor to cool to ambient air temperature. Care should be taken not to ride the brakes into the pits as this may hot spot the rotor causing premature wear to the surface or structural damage.

Specs

Sold in Quantity:
Each
Bolt Pattern:
5 on 4.75"
Finish:
Natural
Rotor Diameter:
11.00
Rotor Construction:
Vented
Material Type:
Cast Iron
Rotor Location:
Front
Rotor Shape:
Round
MFG. Part #:
910-31070
Drilled:
No
Slotted:
No
Stud Length:
0.88
Stud Diameter:
0.43
Rotor Thickness:
0.88
Weight:
20.65

Related Products

More Like This

Reviews

Q & A

Articles

You May Also Like

Suggestions
Error
Note
Ok