Since 1952
America's Oldest Speed Shop ®
Speedway Motors Bill Smith

Flaming River FR1943 Steering Coupler 36-Spline, 3/4 Rnd, Non-Flex Box

SAME DAY SHIPPING!

Specs
Material Type:
Stainless Steel
Overall Length:
2.00
Sold in Quantity:
Each
Finish:
Natural
Shaft Diameter:
.75
Outside Diameter:
1.00
End #1:
3/4 inch Round
Spline OD:
.62
Spline Count:
36
MFG. Part #:
FR1943

Share by Email

From
To

Click image to enlarge

X

Details

Reviews

Q & A

What's in the Box

Couplers are available for direct steering connections where an angle is not required. Couplers can also be used to extend the steering shaft.

Steel coupler is splined on one end and has a 3/4" round hole on the other.

When ordering, select applicable hole size/spline needed.

Coupler = 2" L x 1.060" D

Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

 

You may also be interested in:

Steel Heim Joint Rod Ends for Steering Shaft, 3/4-16 RH Male .757 Hole
                        3/4" heim for steering shaft.  Has .757 ball hole. Slides right over standard 3/4" steering shaft. 3/4" NF right hand threads. Jam nut sold separately.


Sweet Mfg Steering U-Joint, 5/8 Inch 36-Spline, 3/4 Round, Vega/Corvair/GM Rack
                        

Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. This steering universal joint is the highest quality for racing or street use.

  • Full compliment bearings
  • Forged Vanadium steel yokes and u-joint
  • Highest quality for racing or street
  • Features needle bearing u-joints
  • 5/8"-36 Spline
Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

Sweet Mfg Steering U-Joint, 3/4 48-Spline to 3/4 Inch Round, Wilwood/SJ/MGB
                        

Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. These steering universal joints have a 3/4" round weld-on end.

  • Works with: Wilwood, Sweet Jaguar, MGB
  • Full compliment bearings
  • Forged Vanadium steel yokes and u-joint
  • Highest quality for racing or street
  • Features needle bearing u-joints
  • 3/4"-48 Spline
Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

Sweet Mfg Steering U-Joint, 5/8-36 Spline, 3/4 DD, Vega/Corvair/GM Rack
                        

Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. These steering universal joints feature full compliment bearings and a 5/8"-36 spline.

  • Full compliment bearings
  • Forged Vanadium steel yokes and u-joint
  • Highest quality for racing or street
  • Features needle bearing u-joints
  • 5/8"-36 Spline
Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

Sweet Mfg Steering U-Joint, 5/8-36 Spline, 1 Inch DD, Vega/Corvair/GM Rack
                        

Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. These steering universal joints are 5/8"-36 spline and feature forged Vanadium steel yokes.

  • Full compliment bearings
  • Forged Vanadium steel yokes and u-joint
  • Highest quality for racing or street
  • Features needle bearing u-joints
  • 5/8"-36 Spline
Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

Sweet Mfg Steering Coupler, 3/4 30 Spline, 3/4 Rnd Non-Flex, Small GM '78-Up
                        

Steel coupler is splined on one end and has a 3/4" round hole on the other.

When ordering, select applicable hole size/spline needed.

Coupler = 2" L x 1.060" D

Spline Size (Link)

Sweet Mfg Steering Coupler, 3/4 36-Spline, 3/4 Rnd Non-Flex, GM Man/Mustang II
                        

Steel coupler is splined on one end and has a 3/4" round hole on the other. This Mustang II power rack U joint coupler is 2" L x 1.060" D.

When ordering, select applicable hole size/spline needed.

Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

Sweet Mfg Steering Coupler, 13/16 36 Spline, 3/4 Rnd Non-Flex, Big GM Pre '78
                        

Steel coupler is splined on one end and has a 3/4" round hole on the other.

Fits big GM gear box for pre 1978 vehicles.

When ordering, select applicable hole size/spline needed.

Warning: This coupler is splined 13/16 x 36 all the way through.  It fits OK on 3/4" round shaft for welding, even though it has interior splines.

Coupler = 2" L x 1.060" D

Sweet Mfg Steering Coupler, 5/8 36 Spline, 3/4 Rnd Non-Flex, Vega/Corvair/GM
                        Steel coupler is splined on one end and has a 3/4" round hole on the other.  

When ordering, select applicable hole size/spline needed.

Coupler = 2" L x 1.060" D

Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

Sweet Mfg. Steering Coupler, 9/16 Inch 26 Spline to 3/4 Inch Round Non-Flex
                        Steel coupler is splined on one end and has a 3/4" round hole on the other.  

When ordering, select applicable hole size/spline needed.

Coupler = 2" L x 1.060" D

Sweet Mfg. Double Steering U-Joint, 5/8-36 Spline 3/4 Round, Vega/Corvair/GM
                        

Sometimes you need just a little bit more clearance than a standard steering u-joint can give you. Our double u-joints allow up to 70 degrees of angle or 1" of offset for just those occasions. These steering universal joints are made of forged vanadium steel and real needle bearing joints.  5-5/8" overall length.

  • Overall length is 5-1/2”
  • O.D. at ends is 1.12”
  • O.D. in the middle is 1.476”
  • O.D. at caps is 1.350”
  • O.D. at cap retainer screws is 1.545”
  • Length of center section is 2-3/4”
Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

 

3/4 O.D. Solid Steel Steering Shaft
                        These solid steering shafts are made for you to cut to fit. 3/4" O.D. 1018 solid steel shaft. Available in 24", 36", 48", 60" and 72" lengths. 

Steer Shaft Application Chart

Firewall Mount Flanged Bearing for Steering Shaft
                        This firewall mount allows up to 30° of mis-alignment. Includes ball with two pressed steel flanges with 5/16" square mounting holes. 

Choose 3/4" (750) or 1" (1000) shaft size.

91032375-1000

  • Height: .74"
  • Length: 3.00"
  • Width: 1.90"
  • Mount C to C: 2.26"
91032375-750
  • Height: .87"
  • Length: 3.00"
  • Width: 1.90"
  • Mount C to C: 2.26"
Sweet Mfg. Double Steering U-Joint, 5/8 36-Spline to 3/4 DD, Vega/Corvair/GM
                        

Sometimes you need just a little bit more clearance than a standard steering u-joint can give you. Our double u-joints allow up to 70 degrees of angle or 1" of offset for just those occasions. These steering universal joints are made of forged vanadium steel and real needle bearing joints.  5-5/8" overall length.

  • Overall length is 5-1/2”
  • O.D. at ends is 1.12”
  • O.D. in the middle is 1.476”
  • O.D. at caps is 1.350”
  • O.D. at cap retainer screws is 1.545”
  • Length of center section is 2-3/4”
Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

Steering Shaft Aluminum Heim Joint Rod Ends, 3/4-16 RH Male, .757 Hole
                        3/4" heim for steering shaft.  Has .757 ball hole. Slides right over standard 3/4" steering shaft. 3/4" NF right hand threads. Jam nut sold separately.
                    
Sweet Mfg Chrome Steering U-Joint, 5/8-36 Spline to 3/4 DD, Vega, Corvair, GM
                        

Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. These steering universal joints feature a double D end to make use of the double D shaft.

  • Full compliment bearings
  • Forged Vanadium steel yokes and u-joint
  • Highest quality for racing or street
  • Features needle bearing u-joints
  • 5/8"-36 Spline
Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

Sweet Mfg Chrome Steering U-Joint, 5/8-36 Spline to 1 DD, Vega, Corvair, GM
                        

Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. These steering universal joints feature a double D end to make use of the double D shaft.

  • Full compliment bearings
  • Forged Vanadium steel yokes and u-joint
  • Highest quality for racing or street
  • Features needle bearing u-joints
  • 5/8"-36 Spline
Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

Flat Heim Joint Rod End Support Bracket
                        Overall length of 3 1/2 inches long.  Offered with a 3/4 clearances hole for steering heim with a slotted adjustment of 1 7/8 inch long. Bracket is 3/16 thick steel.