Products to Compare (max of 3)
X
Compare These Parts
ALWAYS SECURE
America's Oldest Speed Shop ® Talk to the Experts. Call 800.979.0122, 7am-10pm, everyday.
Filters
Menu
Help Center
Help Center
x
Help Center

U.S.Order Line:

800.979.0122

(CST) 7am - 10pm

Race and Rod Tech Support

Mon-Fri 8am - 5pm

Canadian Order Line:

855.313.9180

International Order Line:

1.402.323.3200
Since 1952
Menu
x

Crane Cams 7501705 1959-74 Ford V8 XRI Points Ignition Conversion Kit

Free Shipping Free Shipping
Specs
Sold in Quantity:
Each
Notes
Includes ballast resistor, coil and ignition module.
Crane Cams 7501705 1959-74 Ford V8 XRI Points Ignition Conversion Kit
VIDEO
Crane Cams 7501705 1959-74 Ford V8 XRI Points Ignition Conversion Kit

Click image to enlarge



Details

Reviews (1)

Q & A (4)

What's in the Box

Info

Here’s the easiest points conversion kit on the market. Simply remove the old points and condenser, install the XR-i electronic ignition module on the supplied adapter plate, and run a couple of wires. Everything fits under the OEM distributor cap so you retain a restoration-perfect “factory look.”  

Each kit includes a Crane PS20 1.4 ohm oil-filled ignition coil with black finish.

  • Never replace points again
  • Easy two wire hookup
  • Improved starting and mileage
  • Built-in 4000-8000 RPM adjustable rev limiter
  • Picks up timing from distributor cam lobe
  • Fully sealed
  • Operating Voltage: 6-18 Volts, reverse polarity protection, negative ground
  • Current Draw: 3 amps max @ 5,500 RPM
  • RPM Operating Range: 6,500 RPM
  • RPM Limiter Range: 4,000 to 8,000 RPM
  • Primary Voltage Output: 400 volts (inductive discharge)
  • Primary Energy utput: 45 millijoules w/ PS20 coil and 1.65L ballast resistor
  • Peak Spark Gap Current: 50 milliamps w/ PS20 Coil and 1.65L ballast resistor
  • Spark Duration: 2100 microseconds @ 2,000 RPM
  • Coil Dimensions: 2-1/8" D x 5-3/4" L, 1.75 lbs.
  • Coil Primary Resistance: 1.4 ohms

Warranties

Crane Cams Warranty

Customer Reviews

Rated 5 out of 5 by 1 reviewers.
RATING BREAKDOWN
1 reviews
5 Stars
1
4 Stars
0
3 Stars
0
2 Stars
0
1 Star
0
RECOMMEND THIS PRODUCT:

Clark1004
Verified Purchaser
Verified Reviewer
Columbia Falls, MT

Crane Cams Points Ignition Conversion Kit for 64 F-100

May 18, 2016
Product was as described
Pros:
  • Easy To Install
  • American Made
Yes, I recommend this product.
Full Size Image

Was this review helpful? 0 0

Page 1 of 1

Product Q&A

4 questions : 4 answers

1 answers

Will this fit Ford FT heavy duty motor distributors (e.g. 391FT) Ford trucks from the '70s used a heavy duty version of the FE block fords, often referred to as the FT motors, like the 391. These motors often have distributors equipped with cable tach-drives and an accommodation for governors. Will this kit fit those Ford distributors as well?

mzerega
San Diego
November 25, 2013

Will this fit Ford FT heavy duty motor distributors (e.g. 391FT) Ford trucks from the '70s used a heavy duty version of the FE block fords, often referred to as the FT motors, like the 391. These motors often have distributors equipped with cable tach-drives and an accommodation for governors. Will this kit fit those Ford distributors as well?

Answers

November 26, 2013
EricM
No this conversion kit will not fit in your distributor with the governor and/or cable tach drive.
1 answers

Will this perform as well as late model HEI? Thanks Kenny

Wolfie
Pendleton,Indiana
January 08, 2012

Will this perform as well as late model HEI? Thanks Kenny

Answers

January 11, 2012
John
Part number 2881705 and 2881715 and more. Distributor performance depends on many things including the electronic components. Distributor shaft, shaft bearings or bushings, and play in any of the mechanical components. This kit allows you to retain the smaller more desirable cap on many hot rod and muscle car applications. This kit will up the voltage as compared to an OEM coil and in turn give you a hotter spark and a more precise spark very similar to or better than an HEI set up.
1 answers

Does this product use a slip over the distributor shaft piece to send current between the pickup and sender like petronix system II . Or does it just sends current off the shaft itself? I have a replacement distributor with a smaller shaft , I am looking

Benny
Vero Beach ,FL
February 16, 2012

Does this product use a slip over the distributor shaft piece to send current between the pickup and sender like petronix system II . Or does it just sends current off the shaft itself? I have a replacement distributor with a smaller shaft , I am looking

Answers

February 20, 2012
John
Part number 2881705 This style of conversion kit picks up the signal from the cam lobe on the distributor shaft itself and does not require a slip over collar or sleeve.
1 answers

Will this work in an Accel 30202 duel point distributor? I'm running a Crane cam #520641, springs # 99838, lifters #99280 all Crane valve train. I don't want to buy a new distributor, but would prefer to upgrade mine. Any help would be great, thanks! Don

Jerry
Ohio
May 21, 2016

Will this work in an Accel 30202 duel point distributor? I'm running a Crane cam #520641, springs # 99838, lifters #99280 all Crane valve train. I don't want to buy a new distributor, but would prefer to upgrade mine. Any help would be great, thanks! Don

Answers

May 24, 2016
Steve
Expert
Yes, this should work with that distributor.
Page 1 of 1

You may also be interested in:

  • Crane Cams 7501700 1959-74 XRi Ford V8 Points Ignition Conversion Kit Crane Cams 7501700 1959-74 XRi Ford V8 Points Ignition Conversion Kit
    View
    (1)
    $79.99
    Compare
  • OTB Gear 6831 Finned Aluminum Coil Mount, Polished OTB Gear 6831 Finned Aluminum Coil Mount, Polished
    View
    (4)
    $64.99
    Compare
  • OTB Gear 6832 Finned Aluminum Coil Mount, Plain OTB Gear 6832 Finned Aluminum Coil Mount, Plain
    View
    (0)
    $49.99
    Compare
Suggestions For You