Since 1952
America's Oldest Speed Shop ®
Speedway Motors Bill Smith
Large Image
CLOSE [X]

Callies SAJ113CC Compstar Comet 4340 Crankshaft Small Block Chevy 383

Price:
$1,025.99
EA
In Stock
Item #:
2492500
Item Details:
This crank is cut for 6 inch or longer rods and it is rough balanced to a 1750 bob weight.
Callies SAJ113CC Compstar Comet 4340 Crankshaft Small Block Chevy 383
Click image to enlarge Click image to enlarge
No video at this time.
 

The Compstar Comet crankshafts from Callies are forged of 4340 steel and have had non-critical material removed to allow these cranks to weigh only 42 lbs. A light rotating assembly allows you to acclelrate faster off the corners. 

Two piece rear main seal, 350 mains.  3.75" stroke.

Email this page
Close [x]
You can send this product by email to a friend!
Enter the required information in the spaces provided below. They will receive an Email with the picture of this product and a link back to our site.
Your Name:
Your Email:
Friends Name:
Friends Email:
Print Page
Our Techs also Suggest the Following:
Clevite H-Series Small Block Chevy Main Bearings
Item #:
757M909H
Clevite H-Series 1969-Up Small Block Chevy Rod Bearings
Item #:
757R663H
You May Also Be Interested In...
  • Clevite H-Series 1969-Up Small Block Chevy Rod Bearings
    Clevite H-Series 1969-Up Small Block Chevy Rod Bearings
    Price: $94.99
    More Info
    Clevite H-Series 1969-Up Small Block Chevy Rod Bearings
    x 
    							                        
    
                                                        Clevite's H-Series was developed primarily for use in NASCAR type racing, but  they are suitable for all types of competition engines. These sets are  specifically for 1969-Up 302-305-327-350 S/B Chevy "Large Journal" engine (with 2.100" rod  journals).
    • Use H-series bearings with crankshafts that have oversize fillets and where engines run in the medium to high RPM range. 
    • H-Series bearings should be used if contact patterns obtained with P-series  parts are too narrow. Contact pattern should ideally cover 2/3 to 3/4 of the  bearing surface. 
    • If you aren't sure which type of performance bearing to start with,  the H-Series will be your best choice.

    H-Series Features (Link)
  • MAHLE Small Block Chevy 383 Flattop Powerpak Pistons, 6 Inch Rods
    MAHLE Small Block Chevy 383 Flattop Powerpak Pistons, 6 Inch Rods
    Price: $674.99
    More Info
    MAHLE Small Block Chevy 383 Flattop Powerpak Pistons, 6 Inch Rods
    x 
    							                        
    
                                                        
    The Mahle PowerPak pistons are a race proven lightweight forged design that are complete with rings, wrist pins and locks. They are also completely phosphate coated plus feature an anti-friction Grafal skirt coating. PowerPak pistons are made from 4032 aluminum alloy to allow for tighter cylinder to wall clearances, and improved temperature stability.
    • Forged piston for performance applications
    • Lightweight slipper kirt forgings
    • Fully-machined crown
    • Grafal anti-Friction coating on skirts
    • Phosphate-coated to reduce micro-welding and pin galling
    • Pin bores finished on CNC boring equipment
    • Deburred
    • High strength, light weight steel pins
    • Race proven round wire locks
    • Low drag ring pak
    • 1.5mm, 1.5mm, 3.0mm file fit performance ring set is included
    For 383 c.i. S/B Chevy (4.000" bore x 3.75" stroke). Choose oversize diameter needed.
    PowerPak Piston Chart (GIF)
  • Callies CSA5700DS2A2AH Compstar S/B Chevy 4340 H-Beam Rods, 5.7 Inch
    Callies CSA5700DS2A2AH Compstar S/B Chevy 4340 H-Beam Rods, 5.7 Inch
    Price: $644.99
    More Info
    Callies CSA5700DS2A2AH Compstar S/B Chevy 4340 H-Beam Rods, 5.7 Inch
    x 
    							                        
    
                                                        
    Compstar connecting rods come standard with ARP 2000 7/16" cap screws. Will clear a .660" lift small base cam with a 4" stroke crank. 
  • Green Plastigauge for Bearing Clearance, .001-.003 Inch
    Green Plastigauge for Bearing Clearance, .001-.003 Inch
    Price: $2.99
    More Info
    Green Plastigauge for Bearing Clearance, .001-.003 Inch
    x 
    							                        
    
                                                        Place a piece of this thread on a rod or main journal, torque cap in place, remove cap and by using the included chart, you know what your bearing clearance is. You should have one of each when assembling your engine. 
  • Scat 4-350-3750-5700 383 Chevy 4340 Forged Crankshaft, 3.75 Stroke
    Scat 4-350-3750-5700 383 Chevy 4340 Forged Crankshaft, 3.75 Stroke
    Price: $599.99
    More Info
    Scat 4-350-3750-5700 383 Chevy 4340 Forged Crankshaft, 3.75 Stroke
    x 
    							                        
    
                                                        
    As you make more and more power it becomes more important to use quality parts. These Scat 4340 forged steel cranks will help keep your motor alive. 
    • For 2-piece rear main blocks
    • 2.100" rod pin
    • 52 lbs.
    • Straight shot & chamfered oil holes
    • Nitride hardened for superior wear reisistance
    • Lightening holes in all rod throws
    • Large radius on all journals
    • Heat treated, shot peened
    • Designed at SCAT
    • Engineered at SCAT
    • Inspected & micropolished at SCAT
    Note: If you are going to run 915-15550 in a sprint car motor, you must have the crank flange turned down prior to balancing the crank to allow it to go through the motor plate. 
  • Scat 435062LW F43 S/B Chevy Crankshaft-3.75 Stroke-350 Main-2.10 Rod
    Scat 435062LW F43 S/B Chevy Crankshaft-3.75 Stroke-350 Main-2.10 Rod
    Price: $859.99
    More Info
    Scat 435062LW F43 S/B Chevy Crankshaft-3.75 Stroke-350 Main-2.10 Rod
    x 
    							                        
    
                                                        
    Lightweight, strong and at a price you can afford. These 4340 forged steel cranks will really make a difference in your performance.
    • Fits small block Chevy with 2-piece rear main seal
    • Straight shot & chamfered oil holes
    • Nitride hardened for superior wear resistance
    • Profiled and pendulum cut counterweights
    • Gun-drilled main line hole for lightening and equalization of crankcase pressure
    • Star tail for reduced weight