ALWAYS SECURE
America's Oldest Speed Shop ® 800.979.0122 Lincoln, NE
Filters
Menu
Contact
Help Center
x
x
How to Contact Us

U.S.Order Line:

800.979.0122

(CST) 7am - 10pm

Race and Rod Tech Support

Mon-Fri 8am - 5pm

Canadian Order Line:

855.313.9180

International Order Line:

1.402.323.3200
Since 1952
Menu
x

Billet Rectangular Fuel Fill Door

SAME DAY SHIPPING! Order within the next 5 hours 5 minutes and receive same day shipping

Specs
Material Type:
Aluminum
Overall Height:
4.25
Overall Length:
5.50
Sold in Quantity:
Each
Overall Thickness:
.38
Finish:
Polished
Hardware Included:
Yes
MFG. Part #:
312515
Garage Sale:
No
Notes
Door is held closed by a magnet.
Billet Rectangular Fuel Fill Door

Click image to enlarge

Details

Reviews

Q & A

What's in the Box

These billet aluminum rectangular fuel fill doors work great in a pick-up bed or any flat surface. Can be flush mounted. Outer dimensions measure 5-1/2" x 4-1/4" while the door itself measures 3-1/4" x 4-1/2".

Mounting hardware includes four studs, nuts and washers.

Notes

  1. There is a 1/8" lip around the outside of the frame to hide any gap between the frame and the cars body.
  2. The door pivots on two roll pins positioned 1" from one end of the door.
  3. No gas tank filler pipe, no gas cap and no instructions are included.

Customer Reviews

Rated 5 out of 5 by 1 reviewers.
RATING BREAKDOWN
1 reviews
5 Stars
1
4 Stars
0
3 Stars
0
2 Stars
0
1 Star
0
RECOMMEND THIS PRODUCT:

Petesrods
Verified Purchaser
Calgary

nice finish, looks good

February 16, 2015
product is good but takes some finess to actually flush mount it on a thin surface with minimal material left to secure after you cut the opening I am satisfied with the overall installation and appearance on my aluminum rear cowl on my T-Bucket
Pros:
  • flush finish looks clean
Cons:
  • spacer clamps needed for actuall flush mount
Yes, I recommend this product.
Full Size Image

Was this review helpful? 0 0

Page 1 of 1

Product Q&A

1 questions : 1 answers

1 answers

Mounting over the ribs in the bed? How does this item mount over the ribs in the bed? It looks like it would not mount flat onto the bed. thanks Joe

jroudej
Lakeville, MN, USA
February 06, 2015

Mounting over the ribs in the bed? How does this item mount over the ribs in the bed? It looks like it would not mount flat onto the bed. thanks Joe

Answers

February 09, 2015
EricM
Yes, if you have the wood bed floor with the ribs it would not mount flush. You would need to start and stop the ribs on both sides of the fuel door and still the ribs would stick up if mounting the fuel door flush.
Page 1 of 1

You may also be interested in:

Billet Oval Fuel Fill Doors
(Part #91076520)
                        

These billet aluminum fuel fill doors work great in a pick-up bed or any flat surface. Can be flush mounted. Oval.

The access door itself measures 5-1/2" long and 3" wide

The hole needed for mounting is approximately 1/8" smaller than the total length and width to allow a nice finished appearance when installed.

Includes studs, nuts and nylon spacers. No gas cap, gas filler or instructions are included.

Mounting hardware included: four studs, nuts and nylon washers.

Item Details

6-3/4" x 4-1/4"
Touch Latch
(Part #91004590)
                        Touch latch works well with our 910-09045 Hinge With Brackets when building fuel doors. Has a variety of uses. Latch is spring loaded and magnetic. Push to release.
                    
Master Cylinder Access Door
(Part #91031252)
                        Made out of .090 aluminum. The dimensions are 8-3/8" x 5-1/4" outside and 7"x 4" inside. Hinged on one end and held down when closed with a touch latch.