Products to Compare (max of 3)
X
Compare These Parts
America's Oldest Speed Shop ® Talk to the Experts. Call 800.979.0122, 7am-10pm, everyday.
Help Center
Help Center

U.S.Order Line:

800.979.0122

(CST) 7am - 10pm

Race and Rod Tech Support

Mon-Fri 8am - 5pm

Canadian Order Line:

855.313.9180

International Order Line:

1.402.323.3200
Since 1952
Menu
Shop By
Support
Account

AFCO 40280 Clutch Slave Hose Kit

AFCO 40280 Clutch Slave Hose Kit

Click image to enlarge

Details

Reviews (0)

Q & A (7)

What's in the Box

Info

Connects clutch master cylinder to clutch slave cylinder.

Customer Reviews

This product has no reviews.

Product Q&A

7 questions : 7 answers

1 answers

Will this fitting connect to a 1991 camaro Borg Warner 5 speed slave cylinder with the locking pin ? street rod drivetrain

barnbuilder
PA
January 05, 2015

Will this fitting connect to a 1991 camaro Borg Warner 5 speed slave cylinder with the locking pin ? street rod drivetrain

Answers

January 05, 2015
EricM
No this will not connect to a 1991 Camaro slave cylinder. Fitting 5151396 may also work for you older Camaro slave but we do not have a good way to verify it. It does work with the 1993 and up Camaro slave cylinders with the LT1 engine and T-56 transmission combination.
1 answers

Could this be used with a hydraulic throwout bearing with 4 AN fittings?

Mitch67
March 16, 2014

Could this be used with a hydraulic throwout bearing with 4 AN fittings?

Answers

March 17, 2014
EricM
Yes the straight end of this hose is AN4 and is intended to be connected to the throwout bearing.
1 answers

What is the length of the hose?

Mitch67
March 13, 2014

What is the length of the hose?

Answers

March 13, 2014
EricM
This is a 36" long hose.
1 answers

what are end sizes

chuck
asheville nc
February 01, 2011

what are end sizes

Answers

February 02, 2011
Jeremy O
Chuck, This kit includes a 36" braided hose.It is straight AN4 on one end, and the other end is 90* with a 3/8-24 inv flare male nut at the end. The kit also includes an adaptor that is 1/8"NPT on the one end, AN4 male on the other end.
1 answers

What kind of adapters would I need to use this Hose to connect these two products? Speedway master cylinder Part # 91025680 Push Type Slave Cylinder Part # 91025605

Big Mike
Tucson, AZ
February 29, 2016

What kind of adapters would I need to use this Hose to connect these two products? Speedway master cylinder Part # 91025680 Push Type Slave Cylinder Part # 91025605

Answers

March 02, 2016
Eric
Expert
The 90 degree end of this hose will connect right to the 91025680 Speedway master cylinder. The 90 degree adapter that is installed in the slave cylinder 91025605 can be removed and replaced with the straight adapter that is included with this hose kit to complete the connection. If you prefer a 90 degree adapter on the slave cylinder then 324962204 can be installed in the slave cylinder to adapt to this AN4 hose.
1 answers

What is the outer diameter of the braided hose Afco 40280. Would like to order clamps to strap it down.

john
Wisconsin
May 23, 2016

What is the outer diameter of the braided hose Afco 40280. Would like to order clamps to strap it down.

Answers

May 24, 2016
Eric
Expert
This hose is approximately 3/8" OD.
1 answers

Do you have these 48" long?

Sam
July 13, 2016

Do you have these 48" long?

Answers

July 14, 2016
Eric
Expert
We apologize, but do not offer this hose in other lengths. We do offer a hose such as 91031895 in a 48" length which can be adapted to a 3/8"-24 inverted flare connection using adapters 6174396.
Page 1 of 1
Suggestions