No items in Shopping Cart
Currie's Universal Hot Rod Ford 9" kit includes a brand new 56" housing, lifetime warranty 31 spline axles, new axle bearings and seals, and new style big Ford ends.
This all-new 9" Ford housing features big bearing ends (bearings included) and lifetime warranty 31-spline axles with dual bolt patterns (5 x 4.5" and 5 x 4.75"). Center sectionNOT included.
Features one piece .200 thick axle tubes with 2-7/8" wheel bearings. Axle tube is machined within .001 of an inch and comes with RH and LH inner axle seals installed. Available 60" on center only and with 5 on 5 bolt pattern.
This 9" Ford panhard bar mounting bracket has several settings so you can adjust roll center to multiple positions. IMCA approved steel construction. Fits 9" Ford rear ends only.
"Forward mount" design provides increased pull bar angle and forward bit during axle wrap-up and chassis lift over conventional mounting positions centered on axle-8 degree pinion angle allows torque link to be mounted 4" ahead and 12" above axle centerline Forward mounting reduces axle wrap-up from 25-33 percent, which provides consistent corner entry handling during axle wrap-down and improves U-joint life.Multiple holes for mounting torque link and dampener shock3/8" holes allow stiffener braces to be added on high horsepower applicationsLaser cut design fits most rear ends. (Some ...
Our economical 9" Ford rear axle housing features a reclaimed center section, new 3" axle tubes, and new-style Ford ends. Total track width is 56" from hub-to-hub. You will need one 26-3/8" long axle and one 28-5/8" long axle.
Our economical 9" Ford rear axle housing features a reclaimed center section, new 3" axle tubes, and new-style Ford ends. Total track width is 56" from hub-to-hub. The pumpkin is centered in the housing, which puts the pinion offset 2-3/8" from center
These 9" Ford link mounts mount top links and 90/10 shocks to 9" Ford rear ends.Mounts top link 9-1/4", 10-3/8" and 11-5/8" above axle center line. The 3 holes are all 3/4".
These 9" Ford top link mounts mount top link and 90/10 shocks to 9" Ford rear ends.3/16" steel.Mounts top link 13-1/2" above axle center line.
MB Mittler Bros. Machine & Tool rear end is available in a 60" or 62" centered width.Includes housing, two 31 spline axles, two 5 on 5" steel hubs, two drive plates, two .810" x 11.75" rotors, and two rotor adaptors with bolts, bearings and seals.
Complete the front and rear suspension assembly on your T roadster chassis with a bolt-on brake kit specifically designed for our '37-'41 Ford style spindles and 9" Ford rear end. Each kit includes all necessary components: new rotors (available with 5-on-4.5" or 5-on-4.75" bolt pattern), remanufactured GM Metric calipers, caliper brackets, brake pads, bearings, seals and hardware. Rear kit bots on new-style Big Ford ends.
Complete the front and rear suspension assembly on your T roadster chassis with a bolt-on brake kit specifically designed for our '49-'54 Chevy style spindles and 9" Ford rear end. Each kit includes all necessary components: new rotors (available with 5-on-4.5" or 5-on-4.75" bolt pattern), remanufactured GM Metric calipers, caliper brackets, brake pads, bearings, seals and hardware. Rear kit bots on new-style Big Ford ends.
Dirtworks 2-link rear suspension kit comes with all of the brackets, nuts, pull-bars, and other components necessary to set up a robust rear suspension system on your IMCA modified racer.Kit includes: 3/4" Swedged Steel Tubes Two 2-Link Brackets Std 3/4" RH & LH Male Heims 9" Ford Torque Link Plates 9" Ford Panhard Bar Mount Rubber Bushing J Bar 5" x 4" Torque Link Spring Pull Bar w/o Spring 3/4" RH & LH Jam Nuts Frame Mount P-Hard Bar Spring Slider Only w/o Ends Std 1/2" RH Male Heims 1/2" ...
Dirtworks 2-link rear suspension kit comes with allof the brackets, nuts, pull-bars, and other components necessary to set up a robust rear suspension system on your IMCA modified racer.Kit includes: LH 4-Bar U-Weld Birdcages 5/8" Swedged Steel Tubes 5/8" Swedged Steel Sleeves Std 5/8" RH & LH Male Heims 9" Ford Torque-Link Plates 9" Ford Panhard Bar Mount Rubber Bushing J Bar 5" x 4" Torque Link Spring Pull Bar w/o Spring Top Link Bushings & Washers Std 3/4" RH Male & Female Heims 3/4" RH & LH Jam Nuts ...
Stock replacement rear spring. 14" tall in free height.Pig tails on both ends like stock spring. 7" diameter.Available in the following rates: 175, 200, 225, 250 and 300 lb.
Winters replacement gaskets for Winters quick change rear ends. Available in economical paper or heavy duty reuseable with a steel core.
Anodized and spring loaded lever securely locks car into gear. Lever is bolted to mounting plates that are welded to chassis. Works with most rear-ends and 40" cable is suitable for most sprint cars and midgets. Cable sold separately.
Bent or broken rear axles? Speedway carries Winters replacement axles both standard and lightweight. Will work for Winters rear ends only.