9 Inch Ford Ring & Pinion, 5.29 Gear Ratio

							                        

                                                        Shows you how to properly install ring and pinion gear sets. Packed with information for correct installation procedures. 
                                                    
						                        

							                        

                                                        We found a limited supply of new small yokes for the 9" Ford.  They accept the 1310 series U-joints (1-1/16" caps x 3-7/32").  Fits standard 28 spline pinion gear.
                                                    
						                        

							                        

                                                        These Ford 9" megalite steel full spools weigh just 5.55 lbs.
Comparison spool weights:
Aluminum - 5.0 lbs.
Lite Steel - 6.0 lbs.
Standard Steel - 8.9 lbs.
Stock carrier with mini spool - 13.7 lbs.
  Note: All Ford 9" full spools use overhaul kit 9190950-31. The 9190950-31 contains the large I.D.  standard O.D. carrier bearings and pinion bearings needed for use with our full  spools. 
If you are using the H.D. nodular iron center section which uses the large  diameter carrier bearings, order kit 9190950-31s, which also includes the large  pinion bearings for use with the Daytona pinion support.
                                                    

						                        

							                        

                                                        Mount this assembly stand to your work bench (or engine stand) and stop wrestling with the third member every time you need to replace a gear set or spool. Saves you time and energy!  Rotates 360° for total access to your assembly.
                                                    
						                        

							                        

                                                        This 9" Ford overhaul kit includes: pinion pilot, pinion shaft, pinion nut, pinion seal, gasket, shims, crush collar, sealant, gear marking grease, brush and Loctite. Ring gear bolts not included. 
NOTE: All Ford 9" full spools use overhaul kit 9190950-31, even if they are a 28-spline spool. The 9190950-31 contains the large I.D. standard O.D. carrier bearings and pinion bearings needed for use with our full spools.
  If you are using the H.D. nodular iron center section which uses the large diameter carrier bearings, order kit 9190950-31s, which also includes the large pinion bearings for use with the Daytona pinion support.
9" Ford Carrier Bearing Chart (GIF)  - Double check your bearing p/n.
                                                    

						                        

							                        

                                                        
Lightweight and standard steel Ford 9" full spools are available with 28 or 31 splines. Standard steel spool weighs 8.9 lbs. The lightweight steel spool, is 6 lbs. 
NOTE: All Ford 9" full spools use overhaul kit #919-0950-31, even if they are a 28 spline spool.  The 919-0950-31 contains the large I.D. standard O.D. carrier bearings and pinion bearings. 
If you are using the H.D. nodular iron center section which use the large diameter carrier bearings, order kit # 919-0950-31s, which also includes the large pinion bearings for use with the Daytona pinion support.
                                                    

						                        

							                        

                                                        We also offer standard gears from 3.50 to 6.50 ratios on our site. See 91919350.
Note:  Circle track racing applications require a minimum of 4 qts. of rear end lube.  Using less than this amount will lead to immediate pinion bearing failure.
 
 
                                                    

						                        

							                        

                                                        These Ford 9" megalite steel full spools weigh just 5.55 lbs.
Comparison spool weights:
Aluminum - 5.0 lbs.
Lite Steel - 6.0 lbs.
Standard Steel - 8.9 lbs.
Stock carrier with mini spool - 13.7 lbs.
  Note: All Ford 9" full spools use overhaul kit 9190950-31, even if they are a 28-spline spool. The 9190950-31 contains the large I.D.  standard O.D. carrier bearings and pinion bearings needed for use with our full  spools. 
If you are using the H.D. nodular iron center section which uses the large  diameter carrier bearings, order kit 9190950-31s, which also includes the large  pinion bearings for use with the Daytona pinion support.
                                                    

						                        

							                        

                                                        
Ultra lightweight ring gear and pinion
Speedway's in house lightening process can remove up to 2.6 lbs of rotating weight from your drive train