9 Inch Ford Ring & Pinion, 5.14 Gear Ratio

							                        

                                                        Shows you how to properly install ring and pinion gear sets. Packed with information for correct installation procedures. 
                                                    
						                        

							                        

                                                        
Whether you're running a stock flattie and rearend or hopped-up overhead and quick change, you need to run a good gear lube. Remember that your rearend was designed fifty plus years ago and needs all the help it can get. The biggest improvement you can give it is a lubricant that will allow the gears to survive the highway speeds that cars see today. L.E. gear oil is what we use in our 350 mph streamliner, that uses a V-8 quick change, without failure. The "red stuff" provides superior lubrication for long gear life. You can't win if you don't finish. We suggest 90 weight for the street and 140 weight for extreme uses.
Formulated using blends of high quality paraffinic and synthetic base fluids
Contains a highly shear stable tackiness
Unique blend of base fluids and thermally stable EP additives
Separates readily from water
Contains non-silicone defoaming additives
Contains no solids
Contains DUOLEC LE's proprietary dual acting liquid wear-reducing and extreme pressure additive
LE Gear Oil Data Sheet (PDF)
                                                    

						                        

							                        

                                                        These Ford 9" megalite steel full spools weigh just 5.55 lbs.
Comparison spool weights:
Aluminum - 5.0 lbs.
Lite Steel - 6.0 lbs.
Standard Steel - 8.9 lbs.
Stock carrier with mini spool - 13.7 lbs.
  Note: All Ford 9" full spools use overhaul kit 9190950-31. The 9190950-31 contains the large I.D.  standard O.D. carrier bearings and pinion bearings needed for use with our full  spools. 
If you are using the H.D. nodular iron center section which uses the large  diameter carrier bearings, order kit 9190950-31s, which also includes the large  pinion bearings for use with the Daytona pinion support.
                                                    

						                        

							                        

                                                        Mount this assembly stand to your work bench (or engine stand) and stop wrestling with the third member every time you need to replace a gear set or spool. Saves you time and energy!  Rotates 360° for total access to your assembly.
                                                    
						                        

							                        

                                                        This 9" Ford overhaul kit includes: pinion pilot, pinion shaft, pinion nut, pinion seal, gasket, shims, crush collar, sealant, gear marking grease, brush and Loctite. Ring gear bolts not included. 
NOTE: All Ford 9" full spools use overhaul kit 9190950-31, even if they are a 28-spline spool. The 9190950-31 contains the large I.D. standard O.D. carrier bearings and pinion bearings needed for use with our full spools.
  If you are using the H.D. nodular iron center section which uses the large diameter carrier bearings, order kit 9190950-31s, which also includes the large pinion bearings for use with the Daytona pinion support.
9" Ford Carrier Bearing Chart (GIF)  - Double check your bearing p/n.
                                                    

						                        

							                        

                                                        
Lightweight and standard steel Ford 9" full spools are available with 28 or 31 splines. Standard steel spool weighs 8.9 lbs. The lightweight steel spool, is 6 lbs. 
NOTE: All Ford 9" full spools use overhaul kit #919-0950-31, even if they are a 28 spline spool.  The 919-0950-31 contains the large I.D. standard O.D. carrier bearings and pinion bearings. 
If you are using the H.D. nodular iron center section which use the large diameter carrier bearings, order kit # 919-0950-31s, which also includes the large pinion bearings for use with the Daytona pinion support.
                                                    

						                        

							                        

                                                        These Ford 9" megalite steel full spools weigh just 5.55 lbs.
Comparison spool weights:
Aluminum - 5.0 lbs.
Lite Steel - 6.0 lbs.
Standard Steel - 8.9 lbs.
Stock carrier with mini spool - 13.7 lbs.
  Note: All Ford 9" full spools use overhaul kit 9190950-31, even if they are a 28-spline spool. The 9190950-31 contains the large I.D.  standard O.D. carrier bearings and pinion bearings needed for use with our full  spools. 
If you are using the H.D. nodular iron center section which uses the large  diameter carrier bearings, order kit 9190950-31s, which also includes the large  pinion bearings for use with the Daytona pinion support.