All brackets are for 3" rear axle application. Low Rear Axle Bracket Mount radius rods lower than rear axle. 3/8" steel. 5-3/4" long. 3/8" holes.
This steel Panhard bar bracket is a single mount, clamp-on style Panhard bracket. Fits 3" axle tubes.
All brackets are for 3" rear axle application. Heavy Duty Rear Axle Bracket 3" rear axle housing. 3/8" steel. 3/8" holes. 5-3/4" long.
Steering column bracket welds to roll cage. 8" long overall, .100" steel, 3/4" slot.
Steel tank mounting brackets for mounting 8" diameter tanks. Each tank mount has 4-3/4" bolt mount centers and is 6" wide overall at the base.
Overall length of 3 1/2 inches long. Offered with a 3/4 clearances hole for steering heim with a slotted adjustment of 1 7/8 inch long. Bracket is 3/16 thick steel.
All brackets are for 3" rear axle application.Heavy Duty Rear Axle Bracket3" rear axle housing. 3/8" steel. 3/8" holes.5-3/4" long.
All brackets are for 3" rear axle application.Low Rear Axle BracketMount radius rods lower than rear axle. 3/8" steel. 5-3/4" long. 3/8" holes.
Weld these brackets to the underside of your low-ridin' 'T' thru 1934 Ford frame rails for a simple, strong place to attach 4-bars or radius rods. Plain steel. NOTE: For use with spherical rod ends.
Winters full floating Ford 9 inch Grand National rear end for Metric chassis features lightweight steel hubs with brake rotor mounts. This Grand National rear end assembly comes complete with a new housing two hubs two brake rotors two solid 31-spline axles two drive flanges ten lug nuts rotor and drive flange bolts along with all the needed bearings and seals.Now available in either a 5on 5" or 5on 4-3/4" bolt pattern and three different widths:58" centered60" centered62" with a 1/2" offset
Weld these brackets to the underside of your low-ridin' 'T' thru 1934 Ford frame rails for a simple strong place to attach 4-bars or radius rods. Plain steel.NOTE: For use with spherical rod ends.
The inside span on this clevis is app. 11/16" and it would use 3/8" bolts or clevis pins. The threads on the shank are 1/2"-20 the thread length is app. 1-1/2". The slot that’s in this clevis is .625 (5/8”) It should fit any standard heim that has a 1/2" hole. Open Wheel Car Parts 1/2 Inch Steel Birdcage Clevis Steel
Winters full floating Ford 9 inch Grand National rear end for Metric chassis features lightweight steel hubs with brake rotor mounts. This Grand National rear end assembly comes complete with a new housing, two hubs, two brake rotors, two solid 31-spline axles, two drive flanges, ten lug nuts, rotor and drive flange bolts along with all the needed bearings and seals. Now available in either a 5 on 5" or 5 on 4-3/4" bolt pattern and three different widths: 58" centered 60" centered 62" with a 1/2" offset
Replacement fuel shut-off valve tab for Sprint car chassis. Steel tab has a 3/16" diameter hole.
Weld these brackets to the underside of your low-ridin' Model T thru 1934 Ford frame rails for a simple strong place to attach radius rods using 11/16” Ford style tie rod ends. Plain steel.
These threaded windshield studs feature a stop and include one stud and one cone nut. They are zinc plated for longevity. Fits1928-31 Model A and 1932-36 Ford.Steel material(1) stud (1) cone nutSold each Not included in our windshield kits.