No items in Shopping Cart
The main issue when dealing with aluminum tubing (or any aluminum for that matter) is that it "work hardens" when it flexes, which can lead to cracks. It is important that the hard line is isolated from vibration and movement.
These 3/8" fuel line kits have a clean look and are easy to install. Choose with or without fuel filter. These fuel inlets for Edelbrock carburetors provide a clean and custom plumbing solution. The drop-down design routes the fuel line on the right-hand (passenger side) of the carburetor below the linkage and choke housing. The 325-8126 includes a barbed end for a push-on 5/16" or 3/8" rubber fuel line. The 325-8131 includes an aluminum fuel filter with a 40 micron filter element and -6 AN female inlet will accept an ...
Speedway Red See-Through Fuel Line is the perfect old-time accent to your multi-carb street rod! This specially-formulated, flexible tubing has a 3/8" inside diameter and comes in 6 foot lengths. You can easily trim it to your needs. Works with normal slip-on hose barb fittings and clamps.
This fuel line is intended to connect two Edelbrock (or Carter) four-barrel carbs on a low-rise 2x4 intake. The inlet fitting thread is 3/8" NPT female, and there is a 1/8" NPT hole that can be used for a fuel pressure gauge. The outlets on this line can be as close together as 6-1/2" and as far apart as 8-1/4". All of the line is anodized blue, except for the central piece of braided stainless steel hose.
2 brass fittings, 14" pipe thread for 38" ID hose, 2 stainless hose clamps per set.
This is the best flaring tool for the money we have found. It has a ratcheting feed screwwith ahardened flaring coneeccentricallymounted inneedle bearings which produces a rolling action for even metal flow. This provides uniform wall thickness without galling.It will put a 37 degree flare in 3/16", 1/4", 5/16", 3/8", 1/2 ", 5/8" and 3/4" tubing. We recommend this tool when flaring 3/16" stainless steel brake line.
These 3/16" mild steel "hard" lines bend easily and smoothly with hand tools, already have a double flare on each end, have male fittings threaded 3/8"-24 installed and have a 45 inverted flare.
Brake and fuel lines are something you should mount right the first time. Using our stainless steel clamps ensures you never have to replace them. Dual clamps have 3/16" on one end with your choice of 3/16", 1/4" or 3/8" on the other end.
Brake and fuel lines are something you should mount right the first time. Using our stainless steel clamps ensures you never have to replace them. Single clamps are available in 3/16", 1/4", 5/16" or 3/8".
Eliminate ugly fittings and adaptors with this chrome dual feed line with mandrel bends and 3/8" hose barb, providing excellent fuel flow. For Holley 4160-style vaccuum secondary (side hung float bowl) 4-BBL carburetors with 8-21/32" centers.
To make your LS1 transplant a little less painful, we put together these kits for you. If you already have a fuel pump in the tank, use the filter/regulator kit 910-12800. This kit includes a high pressure MSD in-line pump capable of 43 gph @ 40 psi or 39 gph @ 80 psi, a filter/regulator assembly, and all necessary fittings (including fuel rail fitting). Pump draws only 5.4 amps and supports up to 500 horsepower. Pump features 3/8" hose barb inlet and 5/16" barb outlet.
Replacement set of O-rings for Kinsler bypass pill holder 3112. Includes (1) small O-ring and (1) largeO-ring.Compatible with both gas and methanol.
Here you get the hose, hose end fittings and fuel pump fitting if required. Choose from push-on steel or aluminum fittingswith blue hose, or aluminum fittings with stainless steel braided hose. AN8 hose only.
This braided pressure gauge line kit makes it a snap to hook up your pressure gauge. Can be used with oil, water, fuel or air. Includes AN 4 braided line, AN4 to 1/8" NPT male and AN4 to 1/8" NPT female. Choose from lengths of 25", 36" or 48".
Includes one chrome 20" line and one chrome 14" line with male inverted flare fittings. Ideal between mechanical fuel pump and carburetor. 5/16" diameter. Bendable.
61764850Overall Length1.750" (1 3/4")Overall Diameter0.853"ColorBlueMaterial TypeAluminumFinishAnodizedSold in QuantityEachNotesSnaps into GM fuel rail.
Stainless steel braided line available in AN6, 8, 10, and 12. This stainless line can also be used for low pressure applications like fuel, water, air or oil. Not to be used for brake or power steering applications.
This brake line kit bridges the gap between our stainless steel -3 ANkit, and our steel inverted flare version. It includes a 25 foot roll of 3/16" steel brake line, four 18" stainless steel braided hoses and enough -3ANfittings to plumb your brake lines.
We offer longer fuel lines to compensate for extra length between fuel bowls.
61764860Material TypeAluminumFinishAnodizedColorBlueSold in QuantityEachNotesSnaps into GM 5/16" fuel line to AN6.
61764853Fitting End ASnaps into 3/8" fuel lineFitting End BAN-6Material TypeAluminumFinishAnodizedColorBlackSold in QuantityEach
61764863Sold in QuantityEachNotesBlack Anodized, Snaps into a GM 5/16" fuel line to a AN6