Since 1952
America's Oldest Speed Shop ®
Speedway Motors Bill Smith

1960-1986 Small Block Chevy Fabricated Valve Covers w/ Holes

SAME DAY SHIPPING!

Share by Email

From
To

Click image to enlarge

X

Please NOTE the following about this product:

  • This item is sold as a pair.

Details

Reviews

Q & A

What's in the Box

Whether you're going for the hardcore race look or just trying to save weight, these fabricated aluminum valve covers are for you! Each cover comes with a single baffeled 1-1/4" hole for PCV or oil fill. Can be painted, polished, or left in bare aluminum finish.

Fits 1960-1986 Small Block Chevy 283-400 c.i. V8.

Grommets & hardware not included. Use a 1-1/4" grommet.

Specs

  • Overall Height:  3-3/8"
  • Overall Width:  5-1/8"
  • Overall Length:  19-1/2" (including mounting flange)
  • Approximately 2" up on sides, the valve cover is beveled inward at about 45 degrees
  • Top-most flat surface is 2" wide
  • 2-3/8” from the mounting surface to the bottom of the baffle
  • Breather Hole:  1-1/4"

Item Details

S/B Chevy 1960-1986

You may also be interested in:

Weld or Bolt-On Fill Cap
                        

Billet aluminum cap and base. Weld or screw to your valve cover, oil tank or rear end. Knurled cap with O-ring seal.

  • 1-1/4" inside diameter
  • 1-1/4"-12 thread pitch
SuperSeal Small Block Chevy Valve Cover Gaskets, Pre 1986
                        

Small Block Chevy (SBC) valve cover gaskets made with a stainless steel frame sandwiched between durometer-tested neoprene rubber. Eliminates leakage caused by internal pressure fluctuations. Won't tear or collapse.

Reusuable. Package of two. 

SuperSeal Illustration (GIF)

 

Billet Style Aluminum Breathers Without PCV Valve
                        Polished aluminum breathers come with rubber grommets for 1.250" hole. 
                    
Billet Style Aluminum Breather With PCV Valve
                        Polished aluminum breathers come with rubber grommets for 1.250" hole. 
                    
1960-1986 Small Block Chevy Fabricated Valve Covers
                        

Whether you're going for the hardcore race look or just trying to save weight, these fabricated aluminum valve covers are for you! These fully welded sheet aluminum covers feature a 1/8" thick flange for a great seal. Can be painted, polished, or left in bare aluminum finish. Bolts and washers included for mounting with valve cover. Gaskets not included.

Fits 1960-1986 Small Block Chevy 283-400 c.i. V8.

No provisions for an oil breather. 

Grommets for Push-In Oil Breathers, 1-1/4 Inch O.D., 1 Inch I.D.
                        

Our replacement 1-1/4" grommets are made of a black neoprene material for extended service life. Can be used as a plug, or a grommet for push-in style oil breather caps by trimming off the bottom.

Fits into a 1-1/4" valve cover hole.

Grommet for Push-In Oil Breather, 1-1/4 Inch O.D., 3/4 Inch I.D.
                        

Our replacement 1-1/4" grommets are made of a black neoprene material for extended service life. Fits into a 1-1/4" valve cover hole.

Speedway 1960-86 Small Block Chevy Valve Cover Gaskets
                        

Our durable small block Chevy cork valve cover gaskets will work on any street or race engine. Gaskets fit '60-'86 "straight" bolt heads.